Call for a Quote: 778.860.6191
Chilliwack Painters | Abbott Painters

Phillip Jeffries

It isn’t tough to hang wallpaper when you have excellent information to follow. Are you excited to enhance your interior?

If you haven’t hung wallpaper before, pick your type wisely by paying attention during the selection process. Installation will vary moderately depending on the type you decide on. The pre-pasted versions feature a dry paste onto the back of the surface. This is activated by using water, whereas unpasted wallpapers need a wet paste employed with installation. Typically, the installation approach is the same although depending on which kind you use the instructions may vary.



Measure, cut, activate with H20 or paste and hang are the general directions for installing wallpaper.

Wall Preparation

Just before started, clear your work space and the surface area. Ensure that all electrical outlets are powered down and take off any wall fixtures. Get rid of any previous wallpaper paste or deposits and clean the walls carefully with TSP before getting started.

Use a premixed general primer for wallpaper to organize your wall. Priming the wall is a crucial step when you are affixing unpasted wallpaper since it allows easier removal of the wallpaper later.

Measure & Activate the Paper

Start with measuring the wall length. Add four inches to this number and then trim your wallpaper. You want the paper to overlap the ceiling and the baseboard by roughly 2 inches.

Generate pattern match via random, straight across, or drop match.



If hanging unpasted wallpaper…

For unpasted wallpaper, many prefer to administer the paste onto the wall, while others use it directly to the wallpaper. If pasting the wall, apply the paste smoothly to the wall, covering a space for one strip exclusively. When pasting the wallpaper, start in the centre and work away towards the edges while you evenly coat the wallpaper. Afterward, carefully fold the pasted sides of the moistened strip alongside one another and allow them to rest for three minutes. This procedure is called booking.

Experiment to determine if you prefer pasting unpasted variations by applying the paste to the paper or the wall. Only deal with one region at a time when you're evenly applying the paste directly on the wall. When you are pasting the wallpaper, diligently apply an even coating to the back of the wallpaper. Begin pasting in the center of the wallpaper and transfer toward the edges. Gently fold the moistened wallpaper strip and maneuver the pasted sides together so the booking strategy can happen. Allow the already folded wallpaper to remain like this for three minutes.

When you are hanging heavier wallpapers that incorporate embroidery, cork, or flock in their design, purchase a heavyweight clear, stain-free pre-mixed paste to handle the surplus weight instead of a light-to-medium product.

When hanging pre-pasted wallpaper…

Have the patterned side in and the pasted side facing out when you cut your strip and roll it. Next, immerse the rolled strip for 30 seconds into warm water to activate the paste. Alternatively, you can use a Wallpaper Hand Sprayer to attain a similar effect by activating the paste using a fine mist of clean water to the pasted segment.

If you are using the hand sprayer, spray in prolonged strokes that are the length of the paper to fully moisten the back of the strip. Concentrate on the edges for even application. Have the pasted edges together by folding each part of the strip toward the center. Ensure the edges don’t dry out by precisely aligning the sides. Delicately roll the strip much like a rolled newspaper and enable it to rest for three minutes. This booking action permits the paste to become totally activated and the paper to relax and become more manageable.



Hanging your first strip

Once the booking is achieved, take your strip to the wall. Carefully unfold the strip and hang it up. Allow the substance to overhang on the ceiling and the baseboard. Clear away any air bubbles using a smoothing brush or wide knife or a plastic smoother. Press the wallpaper to ensure satisfactory wall contact. Take care not to pull or distort the wallpaper. Lightly flatten joints with a seam roller.

Proceeding to the second strip

To apply your next strip, butt it up next to the edge of the first wallpaper strip. Firmly and smoothly press the wallpaper into position. Make sure to wash the ceiling and the baseboard after to get rid of any residual paste. Ideally, your seams really should be vertical with a tight fit. The paste really should be free from air bubbles to get the best results.

After every three sections have been properly installed with the excess mixture removed, take a few steps back and consider your results. Check the panels for color and pattern uniformity. Proceed in the same way, three panels at a stretch around your space. You might require extra time to match up geometrical designs or complex patterns. They may need more selvage trimming to obtain color matching at the seams. Take breaks when you want to rest your arms and your eyes. Don’t hasten your wallpaper venture. Follow the steps above to display the rest of your strips. After all sections have been installed, carefully cut following the ceiling and the baseboards. It is suggested that you depend on a guide and a razor knife to assist in trimming without tearing.

Call Us Today
778.860.6191


Articles & Resources

Paint Primer Guide Paint Primer Guide
Bennett Canada Bennett Canada
How to pick the Right Paint Brush How to pick the Right Paint Brush